Valorization of solid waste in sugar factories with possible applications in India : A review

Sugar production is a major agro-based industry in India that generates various solid wastes viz. sugarcane trash, bagasse, press mud and bagasse fly ash. This work examines the state-of-the-art in innovative value added products that can be obtained from the transformation of these wastes. Challenges in implementing these waste valorization solutions are also highlighted. It is observed that the extent of research and adoption of these solutions vary considerably. Both industry involvement as well as government encouragement is required in translating the research findings into commercial products.     

加速溶剂萃取-固相萃取净化-高效液相色谱法测定玉米作物中多环芳烃含量

建立了加速溶剂萃取-固相萃取净化-高效液相色谱测定玉米作物中15种多环芳烃的方法,优化了试验条件.方法线性关系良好,15种多环芳烃的检出限在0.003 8～0.079μg/kg之间,空白加标试验的相对标准偏差在3.9%～11.7%之间,基质加标回收率在69.3%～115.3%之间.实际样品的测定结果表明,该方法分离效果...     

纤维膜三相液相微萃取在测定偶氮染料降解产生芳香胺中的应用

采用纤维膜保护的三相液相微萃取（HF-LLLME）技术,对偶氮染料在人工汗液和光辐照协同作用下降解产生致癌芳香胺的分析方法进行了研究.选用苯胺、邻甲苯胺、对氯苯胺和对硝基苯胺的汗液混合溶液进行模拟样品预处理,以正辛醇为有机萃取相,在供体相pH值为9,NaC l浓度为200.gL-1,接收相为pH=1的盐酸水溶液,萃取时...     

菌渣中阿维菌素残留检测方法及其无害化工艺研究

文章建立了简单、快速的阿维菌素菌渣中阿维菌素残留量高校液相色谱检测方法以及利用水热法处理阿维菌素菌渣。采用固相萃取-高效液相色谱检测方法测定阿维菌素菌渣中阿维菌素残留量,提取剂为乙腈/水=4/1(V/V),采用HLB固相萃取柱进行净化。加标回收率90.3%~107.3%,相对标准偏差(RSD)为3.00%~5.69%,阿维2菌素标准曲线线性相关系数R~2=0.999 6,线性范围为1.0~1 000 mg/L。利用正交实验,水热法处理阿维菌素菌渣,在190℃的温度下处理2 h后,菌渣中阿维菌素残留量由991.30降至0.84 mg/kg,去除率达99.92%。处理前后的菌渣与有机肥标准作对比,除含水率外其余检测指标均达到有机肥标准要求。该项研究为阿维菌素菌渣的资源化利用提供了理论依据。     

短波长X射线衍射技术及在环境工程中的应用展望

介绍了短波长特征X射线衍射无损检测分析原理和方法,无损地测定了预拉伸铝板、高强钢孔挤压件、铝合金搅拌摩擦焊接件等材料部件的内部残余应力、内部物相、内部织构及其分布,并分析讨论了测试结果。该仪器具有体积小,投资少、使用维护方便等优势,展望了该无损检测分析技术在装备环境工程中的应用前景。     

某城市污水处理厂二期污水处理工程设计研究

详细介绍了某城市第一污水处理厂在现有工程的基础上二期工程的工艺设计以及构筑物、设备参数;二期工程充分利用原有工程场地,本着现有、新建运行管理便捷统一原则,采用改良型A/A/O生化池作为二级处理主体工艺;二期工程投入运营后,某城市污水处理厂达到20×104 m3/d的污水设计规模.最终污水厂出水水质达到了《城镇污水处理厂污染物排放标准》(GB 18918-2002)一级 A排放标准.污水处理厂运营后,经济效益显著,可保本经营,并具有企业自我发展的能力.     

Policy implementation of the Republic Act (RA) No. 9003 in the Philippines: A case study of Cebu city

Municipal Solid Waste Management (MSWM) is considered to be one of the most serious environmental issues in the Philippines. The annual waste generation was estimated at 10.6 million tonnes in 2012 and this is expected to double in 2025. The Republic Act (RA) No. 9003, widely known as the Ecological Solid Waste Management Act of 2000, provides the required policy framework, institutional mechanisms and mandate to the Local Government Units (LGUs) to achieve 25% waste reduction target through establishing an integrated solid waste management plan based on the 3Rs (reduce, reuse and recycling). Although the initial impact of the LGUs is still very limited in implementing the national mandate, this article highlights the successful experiences of Cebu, the second largest city in the Philippines, in reducing its MSW generation by more than 30% in the past three years. This study also explores the implementation process, innovative actions taken by the Cebu City Government in implementing the national mandate at local level and identifies the factors that influence the policy implementation. The findings suggest that the impacts of the national mandate can be achieved if the LGUs have the high degree of political commitment, planning and development of effective local strategies in a collaborative manner to meet with local conditions, partnership building with other stakeholders, capacity development, adequate financing and incentives, and in the close monitoring and evaluation of performance.     

Facilitating substance phase‐out through material information systems and improving environmental impacts in the recycling stage of a product

The amount of electrical and electronic products is increasing rapidly, and this inevitably leads to the generation of large quantities of waste from these goods. Some of the generated e‐waste ends up in regions with sub‐standard recycling systems and may be processed under poor conditions. During uncontrolled incineration, halogenated dioxins and furans can be generated from brominated and chlorinated compounds in the products. In order to reduce the health and environmental risks involved in the recycling stage of the life cycle of electronics, an effective design‐for‐environment process must be established during the product development phase. Knowledge of the chemical substances in the product is crucial to being able to make informed decisions. Through full knowledge of the material content of procured components, phase‐outs of unwanted substances, such as halogenated substances, can be performed in an effective manner. Therefore, information is the key to success in phasing‐out substances; facilitating compliance of legal provisions for manufacturers of electrical and electronic devices; and improving the environmental footprint of products as they reach the end of the life cycle. After an introduction to the challenges of electronics waste management, this paper describes supply chain information systems and how they are used to facilitate substance phase‐outs in the electronics industry. Sony Ericsson has been working with phase‐outs of unwanted substances since it was founded in 2001. Through the introduction of a material declaration system that keeps track of all substances in the components used in the company's products, Sony Ericsson has been able to replace unwanted substances to improve environmental impacts at the recycling stage of a product.     

Detection of DDT and its metabolites in two estuaries of South China using a SPME-based device: First report of p,p′-DDMU in water column

A solid-phase microextration-based sampling method was employed to determine the concentrations of 1,1,1-trichloro-2,2-bis(p-chlorophenyl)ethane (DDT) and its metabolites, 1,1-dichloro-2,2-bis(p-chlorophenyl)ethane (DDD), 1,1-dichloro-2,2-bis(p-chlorophenyl)ethene (DDE) and 1-chloro-2,2-bis(p-chlorophenyl)ethene (DDMU), in two estuarine bays, Daya Bay and Hailing Bay, of South China. Six DDT components including p,p′-DDT, o,p′-DDD, p,p′-DDD, o,p′-DDE, p,p′-DDE, and p,p′-DDMU were detected in Hailing Bay, while only p,p′-DDD was found in Daya Bay. p,p′-DDD was the most abundant DDT component in both bays, sharply different from the previous finding in the water column of the Palos Verdes Shelf, California, USA that p,p′-DDE was prevalent. In addition, the occurrence of p,p′-DDMU (with a range of 0.047-0.21 ng/L in Hailing Bay) has not been reported around the globe, and its presence in our study region appeared to stem from dehydrochlorination of p,p′-DDD, favored under aerobic conditions, but further investigations are clearly needed to confirm the mechanism for generation of DDMU in estuarine environments.     

Determination of direct and fugitive PM emissions in a Mediterranean harbour by means of classic and novel tracer methods

Remodelling works are frequent in harbour areas, given that they must adapt to rapidly changing market requirements. Depending on their nature (construction, demolition, etc.), these works may be carried out during long periods of time and thus exert a significant impact on the air quality at the harbours and their surroundings. The air quality at the Valencia harbour was studied during an enlargement project. Four sampling stations aimed to cover the major dust-emitting activities in the harbour. In addition, a sampling campaign was carried out to collect dust materials at their emission sources (e.g., loading and unloading of clinker and petroleum coke, as well as the enlargement works). Differences obtained between PM levels at the monitoring sites were correlated with the distance between sampling stations and enlargement works and/or harbour operations, as well as with the preferential wind direction. In all cases, the days with the highest PM_10 levels were linked to wind directions coinciding with the location of the enlargement works or the clinker and petroleum coke stocks. Classic source apportionment methodologies (PCA and CMB) were applied to the data, but their interpretation was complex due to the similar chemical signatures of PM originating from direct and fugitive emissions from stocked materials (e.g., clinker), and the enlargement works. To overcome this difficulty, a novel non-statistical approach was used to obtain quantitative estimations of the contributions from sources (petroleum coke and clinker), based on the correlation between specific PM components (e.g., carbonaceous species) and source tracers (e.g., V). Finally, a qualitative test using phenolphthalein was devised to identify the presence of clinker on the filters, which provided positive results. This novel tracer approach is thus recommended for harbour authorities.